The iButton device is ideal for any application where information needs to travel with a person or an object.
Today iButton devices are widely used in various application areas include:
Electronic Asset Control
The iButton device is the ultimate information carrier for automatic identification, secure authentication, and many portable applications.
Use iButtons for Driver Identification
iButton is the technology used by most major fleet operators to identify the drivers in each vehicle of the fleet.
The operation of iButtons is simple yet very effective:
A distinctive key fob is assigned to each driver
A reader is installed in the vehicle which is connected to the GPS tracking device.
When the driver starts the vehicle he is required to present the key fob to the key reader. This associates him with that vehicle.
A LED light gives feed back to the driver that the key has been accepted
Powerful reports are then generated from this collected data. Reports can be run by vehicle or driver for any length of time containing times of log in and outs along with durations.
The reports will tell you, in detail:
Daily detail of the time when drivers start and finish to work
Total hours worked per day, week, month.
Since the iButton logs out the driver after each long stop (predefined by you), you'll learn more about the daily routine of each one of your drivers.
You can also generate summary reports with total hours worked.
Worked hours report per driver can be exported to excel for further analysis
1, Driver authorization – gives ability to use vehicle only for specific iButton owners and identify which driver is on the road.
2, Immobilizer – without iButton authorization you can not run engine starter and and use vehicle.
3, AutoGeofencing – gives ability to know when car leaves customized areas without iButton authorization.
Eelink has designed and developed a new generation of 4G GPS tracker with iButton.
This 4G iButton tracking devices will be your best choice for fleet tracking, supply chain tracking, asset tracking.
Eelink TK419 4G iButton tracking devices features
4G & LTE & 3G
Supporting 4G 3G and 2G network for a wide range of signal coverage
1-wire interface for SOS, Ibutton, and temperature sensor.
Can read driver ID, only authorized driver can ignite the car
Remote Cut-off (Oil/Engine)
Compel the vehicle to stop by breaking off the fuel connection
Movement alarm, low battery alarm, GPS blind area alarm, power-cut alarm, GPS antenna disconnect alarm and Geo-fencing alarm
Multiple I/O Interfaces
3 digital inputs, 2 digital outputs,1 Microphone Socket,1 Speaker Socket,1- Wire Interface
Tracked by: SMS,Web,APP
Real-time tracking the location and status by SMS, Web & APP
|GPS Chip||UBLOX GPS, GNASS Chip|
|Antenna||LTE Antenna Internal,|
|GPS Antenna Internal|
|GPS Positioning Accuracy||5m-15m (Depending on GPS Signal)|
|LBS Positioning Accuracy||~200m (Depending on density of base stations)|
|GPS Frequency||L1, 1575.42MHz C/A code|
|Network||LTE/FDD, WCDMA,GSM, SMS|
|WCDMA Frequency||W800/W850/W900/W1900/W2100 MHz|
|GSM Band||EDGE GPRS(B2/ B3/ B5/ B8) 850, 900, 1800 and 1900MHz|
|LTE Band||FDD(B1/B2/B3/B4/B5/B7/B8/B28); TDD(B40)|
DC-HSDPA B1/ B2/ B5/ B8
|Hot/Warm/Cold Start||<3x, <15s, <60s|
|Main PCB||uBlox LTE Module|
|Built-in Battery||Embedded 3.7V/140mAh battery for emergency alarm when removing main power|
|Work Current||<30 mA|
|Standby Current||<15 uA|
|IP Waterproof Level||IP65|
|Dimensions (mm)||89mm x 37mm x 12mm|
|Operating Voltage||9-72V DC|
-20○C - 75° C
|Environment Humidity||20% ~ 80% RH|
|Battery capacity||140m Ah|
AM 09:00 ~ PM 06:00
86 0755 86278373
Copyright © 2004-2021